[ Upstream commit b2d70c0d ]

make dtbs_check:

    arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dt.yaml: bridge@2c: reg:0:0: 45 was expected

According to the datasheet, the I2C address can be either 0x2c or 0x2d,
depending on the ADDR control input.

Fixes: e3896e6d ("dt-bindings: drm/bridge: Document sn65dsi86 bridge bindings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Link: https://lore.kernel.org/r/08f73c2aa0d4e580303357dfae107d084d962835.1632486753.git.geert+renesas@glider.be


Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 778cb8e3 ]

"PAGESIZE / 512" is the number of ECC chunks.
"ECC_BYTES" is the number of bytes needed to store a single ECC code.
"2" is the space reserved by the bad block marker.

"2 + (PAGESIZE / 512) * ECC_BYTES" should of course be lower or equal
than the total number of OOB bytes, otherwise it won't fit.

Fix the equation by substituting s/>=/<=/.

Suggested-by: Ryan J. Barnett <ryan.barnett@collins.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20210610143945.3504781-1-miquel.raynal@bootlin.com


Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 55c21d57 upstream.

Fix board compatible typo reported by dtbs_check.

Fixes: f4d1577e ("dt-bindings: arm: Convert Tegra board/soc bindings to json-schema")
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20210912165120.188490-1-david@ixit.cz


Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit baf8d689 ]

The PWM pins on North Bridge on Armada 37xx can be configured into PWM
or GPIO functions. When in PWM function, each pin can also be configured
to drive low on 0 and tri-state on 1 (LED mode).

The current definitions handle this by declaring two pin groups for each
pin:
- group "pwmN" with functions "pwm" and "gpio"
- group "ledN_od" ("od" for open drain) with functions "led" and "gpio"

This is semantically incorrect. The correct definition for each pin
should be one group with three functions: "pwm", "led" and "gpio".

Change the "pwmN" groups to support "led" function.

Remove "ledN_od" groups. This cannot break backwards compatibility with
older device trees: no device tree uses it since there is no PWM driver
for this SOC yet. Also "ledN_od" groups are not even documented.

Fixes: b835d695 ("pinctrl: armada-37xx: swap polarity on LED group")
Signed-off-by: Marek Behún <kabel@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210719112938.27594-1-kabel@kernel.org


Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1c8094e3 ]

When the schema fixups are applied to 'select' the result is a single
entry is required for a match, but that will never match as there should
be 2 entries. Also, a 'select' schema should have the widest possible
match, so use 'contains' which matches the compatible string(s) in any
position and not just the first position.

Fixes: 993dcfac ("dt-bindings: riscv: sifive-l2-cache: convert bindings to json-schema")
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 92e66901 ]

The SCL gpio pin used by I2C bus for recovery needs to be configured as
open drain, so fix the binding example accordingly.
In relation with fix c5a28380 ("ARM: dts: at91: Configure I2C SCL
gpio as open drain").

Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Fixes: 19e5cef0 ("dt-bindings: i2c: at91: document optional bus recovery properties")
Signed-off-by: Sasha Levin <sashal@kernel.org>

commit d031d99b upstream.

There is a fair amount of warnings when running 'make dtbs_check' with
amlogic,gx-sound-card.yaml.

Ex:
arch/arm64/boot/dts/amlogic/meson-gxm-q200.dt.yaml: sound: dai-link-0:sound-dai:0:1: missing phandle tag in 0
arch/arm64/boot/dts/amlogic/meson-gxm-q200.dt.yaml: sound: dai-link-0:sound-dai:0:2: missing phandle tag in 0
arch/arm64/boot/dts/amlogic/meson-gxm-q200.dt.yaml: sound: dai-link-0:sound-dai:0: [66, 0, 0] is too long

The reason is that the sound-dai phandle provided has cells, and in such
case the schema should use 'phandle-array' instead of 'phandle'.

Fixes: fd00366b ("ASoC: meson: gx: add sound card dt-binding documentation")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210524093448.357140-1-jbrunet@baylibre.com


Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a7277a73 upstream.

The compatible strings "mediatek,*" appears two times, remove one of them.

Fixes: e69f5dc6 ("dt-bindings: serial: Convert 8250 to json-schema")
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210422090857.583-1-thunder.leizhen@huawei.com


Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7935bb56 upstream.

The "resets" property is not present on R-Car Gen1 SoCs.
Supporting it would require migrating from renesas,cpg-clocks to
renesas,cpg-mssr.

Fixes: 905fc6b1 ("dt-bindings: rcar-vin: Convert bindings to json-schema")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/217c8197efaee7d803b22d433abb0ea8e33b84c6.1619700314.git.geert+renesas@glider.be


Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 9f299d32 ]

To use additional properties 'bluetooth' on serial, need replace false with
'type: object' for 'additionalProperties' to make it as a node, else will
run into dtbs_check warnings.

'arch/arm/boot/dts/stm32h750i-art-pi.dt.yaml: serial@40004800:
'bluetooth' does not match any of the regexes: 'pinctrl-[0-9]+'

Fixes: af1c2d81 ("dt-bindings: serial: Convert STM32 UART to json-schema")
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1616757302-7889-8-git-send-email-dillon.minfei@gmail.com


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

commit af9d316f upstream.

The correct property name is "nvmem-cell-names". This is what:
1. Was originally documented in the ethernet.txt
2. Is used in DTS files
3. Matches standard syntax for phandles
4. Linux net subsystem checks for

Fixes: 9d3de3c5 ("dt-bindings: net: Add YAML schemas for the generic Ethernet options")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f2889889 upstream.

The standard DT property name is "interrupt-names".

Fixes: fd913ef7 ("Bluetooth: btusb: Add out-of-band wakeup support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 322322d1 upstream.

The original fixed-link.txt allowed a pause property for fixed link.
This has been missed in the conversion to yaml format.

Fixes: 9d3de3c5 ("dt-bindings: net: Add YAML schemas for the generic Ethernet options")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1l6W2G-0002Ga-0O@rmk-PC.armlinux.org.uk


Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit f97844f9 ]

The merge resolution of the interaction of commits 307eea32
("dt-bindings: net: renesas,ravb: Add support for r8a774e1 SoC") and
d7adf633 ("dt-bindings: net: renesas,etheravb: Convert to
json-schema") missed that "tx-internal-delay-ps" should be a required
property on RZ/G2H.

Fixes: 8b0308fe ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net"

)
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210105151516.1540653-1-geert+renesas@glider.be


Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4c1e0543 upstream.

The sii902x chip family requires IO and core voltages to reach the
correct voltage before chip initialization. Add binding for describing
the two supplies.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020221501.260025-3-mr.nuke.me@gmail.com


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 320d159e upstream.

Some RTCs, e.g. the pcf2127, can be used as a hardware watchdog. But
if the reset pin is not actually wired up, the driver exposes a
watchdog device that doesn't actually work.

Provide a standard binding that can be used to indicate that a given
RTC can perform a reset of the machine, similar to wakeup-source.

Suggested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201218101054.25416-2-rasmus.villemoes@prevas.dk


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW  = 1 = IRQ_TYPE_EDGE_RISING

Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
  ACTIVE_LOW  => IRQ_TYPE_LEVEL_LOW
  ACTIVE_HIGH => IRQ_TYPE_LEVEL_HIGH

Fixes: a1a8b459 ("NFC: pn544: i2c: Add DTS Documentation")
Fixes: 6be88670 ("NFC: nxp-nci_i2c: Add I2C support to NXP NCI driver")
Fixes: e3b32922 ("dt-bindings: can: tcan4x5x: Update binding to use interrupt property")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for tcan4x5x.txt
Link: https://lore.kernel.org/r/20201026153620.89268-1-krzk@kernel.org


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The RaspberryPi4 has both a WiFi chip and HDMI outputs capable of doing
4k. Unfortunately, the 1440p resolution at 60Hz has a TMDS rate on the
HDMI cable right in the middle of the first Wifi channel.

Add a property to our HDMI controller, that could be reused by other
similar HDMI controllers, to allow the OS to take whatever measure is
necessary to avoid that crosstalk.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029134018.1948636-1-maxime@cerno.tech

Since commit:

    0e030a37 ("can: flexcan: fix endianess detection")

the fsl,imx53-flexcan isn't compatible with the fsl,p1010-flexcan any more. As
the former accesses the IP core in Little Endian mode and the latter uses Big
Endian mode.

With the conversion of the flexcan DT bindings to yaml, the dt_binding_check
this throws the following error:

Documentation/devicetree/bindings/clock/imx5-clock.example.dt.yaml: can@53fc8000: compatible: 'oneOf' conditional failed, one must be fixed:
	['fsl,imx53-flexcan', 'fsl,p1010-flexcan'] is too long
	Additional items are not allowed ('fsl,p1010-flexcan' was unexpected)
	'fsl,imx53-flexcan' is not one of ['fsl,imx7d-flexcan', 'fsl,imx6ul-flexcan', 'fsl,imx6sx-flexcan']
	'fsl,imx53-flexcan' is not one of ['fsl,ls1028ar1-flexcan']
	'fsl,imx6q-flexcan' was expected
	'fsl,lx2160ar1-flexcan' was expected
	From schema: /builds/robherring/linux-dt-bindings/Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml

The error is fixed by replacing the "fsl,p1010-flexcan" compatible
(which turned out the be incompatible) with "fsl,imx25-flexcan" in the
binding example.

Reported-by: Rob Herring <robh+dt@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20201111213548.1621094-1-mkl@pengutronix.de


[robh: Add "fsl,imx25-flexcan" as fallback]
Signed-off-by: Rob Herring <robh@kernel.org>

As both the i.MX35 and i.MX53 flexcan IP cores are compatible to the i.MX25,
they are listed as:

    compatible = "fsl,imx35-flexcan", "fsl,imx25-flexcan";

and:

    compatible = "fsl,imx53-flexcan", "fsl,imx25-flexcan";

in the SoC device trees.

This patch fixes the following errors, which shows up during a dtbs_check:

arch/arm/boot/dts/imx53-ard.dt.yaml: can@53fc8000: compatible: 'oneOf' conditional failed, one must be fixed:
   ['fsl,imx53-flexcan', 'fsl,imx25-flexcan'] is too long
   Additional items are not allowed ('fsl,imx25-flexcan' was unexpected)
   'fsl,imx53-flexcan' is not one of ['fsl,imx7d-flexcan', 'fsl,imx6ul-flexcan', 'fsl,imx6sx-flexcan']
   'fsl,imx53-flexcan' is not one of ['fsl,ls1028ar1-flexcan']
   'fsl,imx6q-flexcan' was expected
   'fsl,lx2160ar1-flexcan' was expected
   From schema: Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml

Fixes: e5ab9aa7 ("dt-bindings: can: flexcan: convert fsl,*flexcan bindings to yaml")
Reported-by: Rob Herring <robh+dt@kernel.org>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20201111130507.1560881-4-mkl@pengutronix.de


[robh: drop singular fsl,imx53-flexcan and fsl,imx35-flexcan]
Signed-off-by: Rob Herring <robh@kernel.org>

The fsl,stop-mode property is a phandle-array and should consist of one phandle
and two 32 bit integers, e.g.:

    fsl,stop-mode = <&gpr 0x34 28>;

This patch fixes the following errors, which shows up during a dtbs_check:

arch/arm/boot/dts/imx6dl-apf6dev.dt.yaml: can@2090000: fsl,stop-mode: [[1, 52, 28]] is too short
    From schema: Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml

Fixes: e5ab9aa7 ("dt-bindings: can: flexcan: convert fsl,*flexcan bindings to yaml")
Reported-by: Rob Herring <robh+dt@kernel.org>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20201111130507.1560881-5-mkl@pengutronix.de


Signed-off-by: Rob Herring <robh@kernel.org>

Add delay to fix pop noise from speaker.

Signed-off-by: Jack Yu <jack.yu@realtek.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201105030804.31115-1-jack.yu@realtek.com


Signed-off-by: Mark Brown <broonie@kernel.org>

In order to automate the verification of DT nodes convert
fsl-flexcan.txt to fsl,flexcan.yaml

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201022075218.11880-3-o.rempel@pengutronix.de


Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

For now we have only node name as common rule for all CAN controllers

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201022075218.11880-2-o.rempel@pengutronix.de


Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

One space has been missing by the diagram update.

Fixes: bb2bd7c7 ("dt-bindings: irqchip: ti, sci-inta: Update for unmapped event handling")
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201103135004.2363-1-peter.ujfalusi@ti.com

The new DMA architecture introduced with AM64 introduced new event types:
unampped events.

These events are mapped within INTA in contrast to other K3 devices where
the events with similar function was originating from the UDMAP or ringacc.

The ti,unmapped-event-sources should contain phandle array to the devices
in the system (typically DMA controllers) from where the unmapped events
originate.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201020073243.19255-2-peter.ujfalusi@ti.com

Several *.txt files got converted to yaml. Update their
references at MAINTAINERS file accordingly.

Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/3b58afec5195d4ea505ea9b3f74d53f7abed4e6f.1603791716.git.mchehab+huawei@kernel.org


Signed-off-by: Jonathan Corbet <corbet@lwn.net>

Another round of wack-a-mole. The json-schema default is additional
unknown properties are allowed, but for DT all properties should be
defined.

Signed-off-by: Rob Herring <robh@kernel.org>

In order to add meta-schema checks for additional/unevaluatedProperties
being present, all schema need to make this explicit. As the top-level
board/SoC schemas always have additional properties, add
'additionalProperties: true'.

Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201005183830.486085-4-robh@kernel.org


Signed-off-by: Rob Herring <robh@kernel.org>

Clean-up incorrect indentation, extra spaces, and missing EOF newline in
schema files. Most of the clean-ups are for list indentation which
should always be 2 spaces more than the preceding keyword.

Found with yamllint (now integrated into the checks).

Cc: linux-arm-kernel@lists.infradead.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-i2c@vger.kernel.org
Cc: linux-iio@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Cc: linux-serial@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Sam Ravnborg <sam@ravnborg.org> # for display
Acked-by:  Jonathan Cameron <Jonathan.Cameron@huawei.com> #for-iio
Signed-off-by: Rob Herring <robh@kernel.org>

Add missing properties that are currently used in the examples of
subnode bindings and in many DTs.

Also updates the example in sound/google,cros-ec-codec.yaml to comply
with the google,cros-ec binding.

Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Link: https://lore.kernel.org/r/20201021114308.25485-4-ricardo.canuelo@collabora.com


[robh: Add missing '#address-cells' and '#size-cells']
Signed-off-by: Rob Herring <robh@kernel.org>

Convert the google,cros-ec-keyb binding to YAML and add it as a property
of google,cros-ec.yaml

Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Link: https://lore.kernel.org/r/20201021114308.25485-3-ricardo.canuelo@collabora.com


Signed-off-by: Rob Herring <robh@kernel.org>

Convert the google,cros-ec-i2c-tunnel binding to YAML and add it as a
property of google,cros-ec.yaml.

Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Link: https://lore.kernel.org/r/20201021114308.25485-2-ricardo.canuelo@collabora.com


[robh: add ref to i2c-controller.yaml]
Signed-off-by: Rob Herring <robh@kernel.org>

Add compatible string for V3s, with H3 one as fallback.

This is used in device tree now, but not standardized in DT binding.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201003235018.1121618-2-icenowy@aosc.io


Signed-off-by: Arnd Bergmann <arnd@arndb.de>

As the binding documentation says, #mbox-cells must have a value of 2,
but the example use a value 3. The MT8173 device tree correctly use
mbox-cells = <2>. This commit fixes the example.

Fixes: 19d8e335 ("dt-binding: gce: remove atomic_exec in mboxes property")
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Link: https://lore.kernel.org/r/20201018193016.3339045-1-fparent@baylibre.com


Signed-off-by: Rob Herring <robh@kernel.org>

Update the leds/common.yaml to indicate that the max color ID is 9.
Reflect the same change in the leds-class-multicolor.yaml

Reported-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20201016115703.30184-1-dmurphy@ti.com


Signed-off-by: Rob Herring <robh@kernel.org>

We need to reset both for the panel to show an image.

Fixes: b9ab1248 ("dt-bindings: Add Mantix MLAF057WE51-X panel bindings")
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/15d3dc7eb4e031f380be1298ed3ac9085626f26b.1602584953.git.agx@sigxcpu.org

Since commit bbc4d71d ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the Realtek PHY driver will override any TX/RX delay
set by hardware straps if the phy-mode device property does not match.

This is causing problems on SynQuacer based platforms (the only SoC
that incorporates the netsec hardware), since many were built with
this Realtek PHY, and shipped with firmware that defines the phy-mode
as 'rgmii', even though the PHY is configured for TX and RX delay using
pull-ups.

From the driver's perspective, we should not make any assumptions in
the general case that the PHY hardware does not require any initial
configuration. However, the situation is slightly different for ACPI
boot, since it implies rich firmware with AML abstractions to handle
hardware details that are not exposed to the OS. So in the ACPI case,
it is reasonable to assume that the PHY comes up in the right mode,
regardless of whether the mode is set by straps, by boot time firmware
or by AML executed by the ACPI interpreter.

So let's ignore the 'phy-mode' device property when probing the netsec
driver in ACPI mode, and hardcode the mode to PHY_INTERFACE_MODE_NA,
which should work with any PHY provided that it is configured by the
time the driver attaches to it. While at it, document that omitting
the mode is permitted for DT probing as well, by setting the phy-mode
DT property to the empty string.

Fixes: 533dd11a ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201018163625.2392-1-ardb@kernel.org


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Document the Microcrystal RV-3032 device tree bindings

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201013144110.1942218-2-alexandre.belloni@bootlin.com

Some RTCs have a trickle charge that is able to output different voltages
depending on the type of the connected auxiliary power (battery, supercap,
...). Add a property allowing to specify the necessary voltage.

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201013144110.1942218-1-alexandre.belloni@bootlin.com