C61: build images can be flashed but cannot be loaded
The flashing issue #464 (closed) was fixed and closed. I retried the latest build for c61 in LAVA. The images can be flashed, but cannot be loaded. The below error reported.
U-Boot SPL 2021.04-ohos/develop/imx_5.10.35_2.0.0+g76566c255c (Jan 31 2022 - 12:31:51 +0000)
power_bd71837_init
C61 is 4GB
DDRINFO: start DRAM init
DDRINFO: DRAM rate 3000MTS
DDRINFO:ddrphy calibration done
DDRINFO: ddrmix config done
Normal Boot
Trying to boot from MMC2
NOTICE: BL31: v2.4(release):lf-5.10.72-2.2.0-0-g5782363f9
NOTICE: BL31: Built : 12:17:17, Nov 18 2021
U-Boot 2021.04-ohos/develop/imx_5.10.35_2.0.0+g76566c255c (Jan 31 2022 - 12:31:51 +0000)
CPU: i.MX8MMQ rev1.0 at 1200 MHz
Reset cause: POR
Model: SECO i.MX8MM C61 board
DRAM: 4 GiB
MMC: FSL_SDHC: 1, FSL_SDHC: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
BuildInfo:
- ATF 5782363
flash target is MMC:0
Net: eth0: ethernet@30be0000
Fastboot: Normal
Normal Boot
Hit any key to stop autoboot: 2 1 0
starting USB...
Bus usb@32e40000: usb dr_mode not found
Port not available.
Bus usb@32e50000: USB EHCI 1.00
scanning bus usb@32e50000 for devices... 2 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Device 0: unknown device
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
7[r[999;999H[6n8Card did not respond to voltage select! : -110
Scanning disk mmc@30b50000.blk...
Disk mmc@30b50000.blk not ready
Scanning disk mmc@30b60000.blk...
** Unrecognized filesystem type **
** Unrecognized filesystem type **
** Unrecognized filesystem type **
Found 8 disks
No EFI system partition
BootOrder not defined
EFI boot manager: Cannot load any image
Card did not respond to voltage select! : -110
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
BOOTP broadcast 6
DHCP client bound to address 10.255.0.160 (6766 ms)
*** Warning: no boot file name; using '0AFF00A0.img'
Using ethernet@30be0000 device
TFTP from server 10.255.0.250; our IP address is 10.255.0.160
Filename '0AFF00A0.img'.
Load address: 0x40280000
Loading: *T T T T T T T T T T
Retry count exceeded; starting again
missing environment variable: pxefile_addr_r
BOOTP broadcast 1
DHCP client bound to address 10.255.0.160 (17 ms)
Using ethernet@30be0000 device
TFTP from server 10.255.0.250; our IP address is 10.255.0.160
Filename 'boot.scr.uimg'.
Load address: 0x43500000
Loading: *T T T T T T T T T T
Retry count exceeded; starting again
BOOTP broadcast 1
DHCP client bound to address 10.255.0.160 (3 ms)
Using ethernet@30be0000 device
TFTP from server 10.255.0.250; our IP address is 10.255.0.160
Filename 'boot.scr.uimg'.
Load address: 0x40280000
Loading: *T T T T T T T T T T
Retry count exceeded; starting again
switch to partitions #0, OK
mmc0(part 0) is current device
Failed to load 'seco-imx8mm-c61.dtb'
switch to partitions #0, OK
mmc0(part 0) is current device
Failed to load 'seco-imx8mm-c61-video-sn65dsi84.dtbo'
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
No FDT memory address configured. Please configure
the FDT address via \"fdt addr <address>\" command.
Aborting!
No FDT memory address configured. Please configure
the FDT address via \"fdt addr <address>\" command.
Aborting!
Trying to boot via UEFI variables Boot####, BootOrder, and BootNext...
ERROR: invalid device tree
No entries from ubootefi.var or they are all invalid...Running directly via UEFI binary...
switch to partitions #0, OK
mmc0(part 0) is current device
** Unrecognized filesystem type **
Can't set block device
ERROR: invalid device tree