From 638dde8d3bf08ccb87863fec2064b25e89f3c664 Mon Sep 17 00:00:00 2001
From: Natalia Kovalenko <waykovalenko@gmail.com>
Date: Tue, 12 Jul 2022 17:55:56 +0200
Subject: [PATCH] Integrate meta-seco-rockchip in oniro
manifests/default.xml: Add new project meta-seco-rockchip
local.conf.sample: Add seco-px30-d23 to MACHINE
bblayers.conf.sample: Add meta-seco-rockchip layer to BBLAYERS
conf-notes.txt Add seco-px30-d23 to supported machines
machines-and-flavours.yaml Add linux-seco-px30-d23 and linux-seco-px30-d23-extra jobs
linux-flavour.rst: Add seco-px30-d23 to supported machines
machines-and-flavours.rst Add linux-seco-px30-d23 job
boards/index.rst Add seco-px30-d23 to supported boards
Add the seco-px30-d23.rst file representing the new Seco's
JUNO board (SBC-D23) in the oniro project.
Signed-off-by: Natalia Kovalenko <waykovalenko@gmail.com>
---
.oniro-ci/machines-and-flavours.yaml | 11 +
docs/build-flavours/linux-flavour.rst | 1 +
docs/ci/machines-and-flavours.rst | 13 ++
docs/hardware-support/boards/index.rst | 1 +
.../hardware-support/boards/seco-px30-d23.rst | 190 ++++++++++++++++++
flavours/linux/bblayers.conf.sample | 1 +
flavours/linux/conf-notes.txt | 1 +
flavours/linux/local.conf.sample | 1 +
manifests/default.xml | 1 +
9 files changed, 220 insertions(+)
create mode 100644 docs/hardware-support/boards/seco-px30-d23.rst
diff --git a/.oniro-ci/machines-and-flavours.yaml b/.oniro-ci/machines-and-flavours.yaml
index db1dcbf7..6a3855ff 100644
--- a/.oniro-ci/machines-and-flavours.yaml
+++ b/.oniro-ci/machines-and-flavours.yaml
@@ -131,6 +131,17 @@ linux-seco-imx8mm-c61-4gb-extra-gcc:
linux-seco-imx8mm-c61-4gb-extra-clang:
extends: [.linux-seco-imx8mm-c61-4gb-extra, .toolchain-clang, .broken]
+.linux-seco-px30-d23:
+ extends: .build-wic-image
+ variables:
+ CI_ONIRO_BUILD_FLAVOUR: linux
+ CI_ONIRO_RECIPE_NAME: oniro-image-base
+ MACHINE: seco-px30-d23
+linux-seco-px30-d23-gcc:
+ extends: [.linux-seco-px30-d23, .toolchain-gcc]
+linux-seco-px30-d23-clang:
+ extends: [.linux-seco-px30-d23, .toolchain-clang]
+
.linux-raspberrypi4-64:
extends: [.build-wic-image, .check-abi]
variables:
diff --git a/docs/build-flavours/linux-flavour.rst b/docs/build-flavours/linux-flavour.rst
index 49739821..7da8a236 100644
--- a/docs/build-flavours/linux-flavour.rst
+++ b/docs/build-flavours/linux-flavour.rst
@@ -27,6 +27,7 @@ Supported machines (default in **bold**):
* seco-intel-b68 (SECO SBC-B68)
* seco-imx8mm-c61-2gb (SECO SBC-C61 2GB DRAM)
* seco-imx8mm-c61-4gb (SECO SBC-C61 4GB DRAM)
+* seco-px30-d23 (SECO SBC-D23)
Build steps example:
diff --git a/docs/ci/machines-and-flavours.rst b/docs/ci/machines-and-flavours.rst
index 8d86ada7..982db7b0 100644
--- a/docs/ci/machines-and-flavours.rst
+++ b/docs/ci/machines-and-flavours.rst
@@ -66,6 +66,19 @@ architecture.
The cache for this job is not public, as it contains proprietary elements
that cannot be redistributed without an agreement with Freescale.
+linux-seco-px30-d23
+...................
+
+This job extends `.build-wic-image` job from the manifest repository and builds
+``oniro-image-base`` using the Linux flavour of |main_project_name| and
+``MACHINE=seco-px30-d23``. This job checks that |main_project_name| software can
+be built for the SECO D23 development board which features a Rockchip PX30 SoC
+(64bit ARMv8-A) architecture.
+
+.. note::
+ The cache for this job is not public, pending legal review of any firmware
+ that may be included.
+
linux-raspberrypi4-64
.....................
diff --git a/docs/hardware-support/boards/index.rst b/docs/hardware-support/boards/index.rst
index 9fbbdd58..44892294 100644
--- a/docs/hardware-support/boards/index.rst
+++ b/docs/hardware-support/boards/index.rst
@@ -17,6 +17,7 @@ This section details the boards supported as part of |main_project_name|.
96b-nitrogen
seco-intel-b68
seco-imx8mm-c61
+ seco-px30-d23
raspberrypi4
arduino-nano-33-ble
nRF52840-DK
diff --git a/docs/hardware-support/boards/seco-px30-d23.rst b/docs/hardware-support/boards/seco-px30-d23.rst
new file mode 100644
index 00000000..856e511a
--- /dev/null
+++ b/docs/hardware-support/boards/seco-px30-d23.rst
@@ -0,0 +1,190 @@
+.. SPDX-FileCopyrightText: Huawei Inc.
+..
+.. SPDX-License-Identifier: CC-BY-4.0
+
+.. _SupportedBoardSecoD23:
+
+JUNO (SBC-D23) SECO
+###################
+
+.. contents::
+ :depth: 3
+
+Overview
+********
+
+JUNO (SBC-D23) is a Single Board Computer based on embedded Rockchip PX30 Processor, featuring Quad-Core ARM® Cortex®-A35 processor.
+The processor integrates a Mali-G31 GPU with High performance dedicated 2D processor, supporting OpenGL® ES 1.1 / 2.0 / 3.2,
+Vulkan 1.0, OpenCL 2.0 and Open VG 1.1. Embedded VPU is able to support video decoding of the most common coding standard (MPEG-4,
+H.265/HEVC, H.264, VP8, VC-1). The board is completed with up to 4GB LPDDR4-3200 32-bit bus memory directly soldered on board and
+one eMMC 5.1 Flash Drive with up to 64GB of capacity. LVDS Single Channel interface and HDMI are supported. The RMII interface and
+Micrel KSZ8091 Ethernet Transceiver allow the implementation of a Fast Ethernet interface. The networking capabilities can be extended
+by WiFi+BT M.2 module and external modem module. The audio functionalities are managed by the AudioCodec embedded in the RK-809 PMIC.
+The JUNO board is completed by a series of connectors with various interfaces (UART, SPI, I2C) managed by the microcontroller STM32F302VCT6.
+
+Hardware
+********
+* For product specification of JUNO (SBC-D23) SECO board, see `Juno page <https://edge.seco.com/it/juno.html>`_.
+* For more detailed specifications, see `User Manual <https://www.seco.com/Manuals/SBC-D23_Manual.pdf>`__.
+
+Working with the Board
+**********************
+
+Building an Oniro image
+=======================
+
+To clone the source code, perform the procedure in: :ref:`Setting up a repo workspace <RepoWorkspace>`.
+
+Linux image
+-----------
+
+1. Source the environment with proper template settings, flavour being ``linux`` and target machine being ``seco-px30-d23``.
+
+.. code-block:: console
+
+ $ TEMPLATECONF=../oniro/flavours/linux . ./oe-core/oe-init-build-env build-oniro-linux
+
+2. You will find yourself in the newly created build directory. Call ``bitbake`` to build the image. The supported image is ``oniro-image-base``.
+
+.. code-block:: console
+
+ $ MACHINE=seco-px30-d23 bitbake oniro-image-base
+
+You can set-up MACHINE variable in ``conf/local.conf`` file under the build
+directory, or via the command line.
+
+Flashing an Oniro image
+***********************
+
+Linux image
+===========
+
+MMC Storage
+-----------
+
+**Prerequisites**
+
+* USB to TTL Serial cable
+* USB Host Type-A to USB OTG interface on USB recovery connector cable (programming cable)
+* Linux Host machine
+
+For detailed information on connectors, refer to the User Manual mentioned above.
+
+After the image is built, you are ready to burn the generated image into the eMMC.
+Build artifacts and update utilities are located in path ./tmp/deploy/images/seco-px30-d23/, relative to the build directory.
+
+To flash Oniro image perform the following steps:
+
+1. Perform the next two steps to view the boot console output
+
+* Connect the host machine USB port type-A with Debug UART connector (CN 27) on the board over USB to TTL Serial cable.
+
+* Open in the terminal your preferred serial port communication program (minicom or gtkterm, for example) and configure
+ the serial port (port: dev/ttyUSB0, baud rate: 115200, data bits: 8, stop bit: 1, parity: none, flow control: none).
+
+2. Put your device into Rockusb mode.
+
+For more details about this mode, see `Wiki Rockusb <http://opensource.rock-chips.com/wiki_Rockusb>`__.
+
+.. note::
+ When there is no bootable firmware on the board, the SoC will run Rockusb driver automatically from its on-chip ROM boot code.
+ In this case, skip the next two steps.
+
+3. Power on the board and stop boot process within boot delay (5 seconds), using combination of the keys ``Ctrl+C``
+
+4. In the U-Boot shell run command:
+
+.. code-block:: console
+
+ => mmc erase 0x4000 0x2000
+
+This command will erase u-boot from eMMC and in this way the board will enter into Rockusb mode on the next power on.
+
+5. Connect the host machine USB port type-A with USB recovery connector (CN7) on the board over the programming cable.
+
+6. Power OFF/ON the board.
+
+7. Check if on your host machine the board has appeared as USB device:
+
+.. code-block:: console
+
+ $ lsusb | grep Rockchip
+
+You will see the command output like this :
+
+.. code-block:: console
+
+ Bus 001 Device 010: ID 2207:330d Fuzhou Rockchip Electronics Company
+
+8. Burn image into eMMC
+
+For example, if you are building oniro-image-base run the following commands:
+
+.. code-block:: console
+
+ $ cd tmp/deploy/images/seco-px30-d23
+ $ chmod u+x flash_d23.sh
+ $ sudo ./flash_d23.sh -a oniro-image-base-seco-px30-d23-emmc.wic
+
+After the image has been successfully burned into the emmc, unplug the programming cable from the host machine.
+
+9. Power OFF/ON the board.
+
+Testing the Board
+*****************
+
+Ethernet
+========
+
+You can use standard tools like ``ip``, ``ifconfig`` to configure and ``ping`` to test the connection.
+
+::
+
+ root@seco-px30-d23:~# ifconfig
+ eth0 Link encap:Ethernet HWaddr C6:73:F6:CB:81:BE
+ inet addr:192.168.1.200 Bcast:192.168.1.255 Mask:255.255.255.0
+ inet6 addr: fe80::56a3:8c7:961e:fd8/64 Scope:Link
+ UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
+ RX packets:205 errors:0 dropped:55 overruns:0 frame:0
+ TX packets:71 errors:0 dropped:0 overruns:0 carrier:0
+ collisions:0 txqueuelen:1000
+ RX bytes:13783 (13.4 KiB) TX bytes:8885 (8.6 KiB)
+ Interrupt:33
+
+ root@seco-px30-d23:~# ping www.google.com
+ PING www.google.com (172.217.168.68): 56 data bytes
+ 64 bytes from 172.217.168.68: seq=0 ttl=113 time=6.983 ms
+ 64 bytes from 172.217.168.68: seq=1 ttl=113 time=6.757 ms
+ 64 bytes from 172.217.168.68: seq=2 ttl=113 time=7.445 ms
+
+ --- www.google.com ping statistics ---
+ 3 packets transmitted, 3 packets received, 0% packet loss
+ round-trip min/avg/max = 6.757/7.061/7.445 ms
+
+USB Host
+========
+
+::
+
+ root@seco-px30-d23:~# lsusb
+ Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
+ Bus 001 Device 002: ID 0424:2514 Microchip Technology, Inc. (formerly SMSC) USB 2.0 Hub
+ Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
+ Bus 003 Device 003: ID 0781:5591 SanDisk Corp. Ultra Flair
+ Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
+
+eMMC
+====
+
+::
+
+ root@seco-px30-d23:~# dmesg | grep mmc0
+ [ 3.816535] mmc_host mmc0: card is non-removable.
+ [ 3.829634] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
+ [ 3.966802] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
+ [ 3.984843] mmc0: new high speed MMC card at address 0001
+ [ 3.995157] mmcblk0: mmc0:0001 DG4016 14.7 GiB
+ [ 4.003237] mmcblk0boot0: mmc0:0001 DG4016 partition 1 4.00 MiB
+ [ 4.012302] mmcblk0boot1: mmc0:0001 DG4016 partition 2 4.00 MiB
+ [ 4.027241] mmcblk0rpmb: mmc0:0001 DG4016 partition 3 4.00 MiB, chardev (241:0)
+
diff --git a/flavours/linux/bblayers.conf.sample b/flavours/linux/bblayers.conf.sample
index e0af5fcf..d5848913 100644
--- a/flavours/linux/bblayers.conf.sample
+++ b/flavours/linux/bblayers.conf.sample
@@ -34,4 +34,5 @@ BBLAYERS ?= " \
##OEROOT##/../meta-riscv \
##OEROOT##/../meta-rauc \
##OEROOT##/../meta-java \
+ ##OEROOT##/../meta-seco-rockchip \
"
diff --git a/flavours/linux/conf-notes.txt b/flavours/linux/conf-notes.txt
index 0e96c994..2f8fbb77 100644
--- a/flavours/linux/conf-notes.txt
+++ b/flavours/linux/conf-notes.txt
@@ -17,6 +17,7 @@ Supported machines (first is the default):
- seco-intel-b68 (SECO SBC-B68)
- seco-imx8mm-c61-2gb (SECO SBC-C61 2GB DRAM)
- seco-imx8mm-c61-4gb (SECO SBC-C61 4GB DRAM)
+- seco-px30-d23 (SECO SBC-D23)
- raspberrypi4-64
MACHINE variable can be set up in conf/local.conf file under build directory
diff --git a/flavours/linux/local.conf.sample b/flavours/linux/local.conf.sample
index 552d64a2..73817506 100644
--- a/flavours/linux/local.conf.sample
+++ b/flavours/linux/local.conf.sample
@@ -25,6 +25,7 @@
#MACHINE ?= "seco-intel-b68"
#MACHINE ?= "seco-imx8mm-c61-2gb"
#MACHINE ?= "seco-imx8mm-c61-4gb"
+#MACHINE ?= "seco-px30-d23"
#MACHINE ?= "raspberrypi4-64"
#
# This sets the default machine to be qemux86 if no other machine is selected:
diff --git a/manifests/default.xml b/manifests/default.xml
index e94007eb..6eeeaa21 100644
--- a/manifests/default.xml
+++ b/manifests/default.xml
@@ -39,6 +39,7 @@ SPDX-FileCopyrightText: Huawei Inc.
<project name="meta-arm" remote="yocto" revision="78fce73c3803aba82149a3a03fde1b708f5424fa" path="meta-arm" />
<project name="meta-java" remote="yocto" revision="1a8059f6b257ebe6fcae6416e499784d976afd24" path="meta-java" />
<project name="jiazhang0/meta-secure-core" remote="github" revision="d0a02859719f1a2c6b98d9d9afe785ec8535ec32" path="meta-secure-core" />
+ <project name="pub/rockchip/meta-seco-rockchip" remote="seco" revision="7aa0714b2c36655bf401e1066e841066f0f323c6" path="meta-seco-rockchip" />
<!--
All entries above are pinned to a specific revision and updated manually.
--
GitLab